|
Post by Robert Arosteguy on Jul 10, 2007 11:52:13 GMT
|
|
|
Post by daniyal on Jul 10, 2007 16:43:10 GMT
Glossy paper i think. I heard the color comes off from photography paper when moist (wet). Even i would like to know how the technique used gives your model a *bling* *bling* shine...
|
|
|
Post by igoraf on Jul 10, 2007 23:33:45 GMT
I don't think so. There are other photos and one of then shows a varnish spray. Some of then can give this "brightness" in papers.
|
|
|
Post by daniyal on Jul 11, 2007 17:21:26 GMT
Yes, it seems like it's some type of color or varnish spray. Doesn't that spoil the paper?? Anyways, notice that the white has gone from the model and white has become yellowish or offwhite. That could be a drawback to this type of technique.
|
|
|
Post by kummisaabas on Jul 13, 2007 18:50:35 GMT
I use white wood glue to make my models glossy because it is most availablefor me. When dried it becomes totally clear and doesn't change colour. In mi opinion it's a big drawback if model's color comes out different from original.
|
|
|
Post by dizudasky on Jul 16, 2007 15:50:37 GMT
hello all just a question: does the white glue soft the model while is drying? Im trying the clear with art varnish for guoache but i guess is not the rigth thing, Please help me .....!!!!!!
|
|
|
Post by dansls1 on Jul 16, 2007 18:28:57 GMT
I've seen airplane models sprayed with a krylon clear gloss spray (spraypaint) that looked pretty good.
|
|
|
Post by jyduchene on Jul 16, 2007 21:28:33 GMT
I have just sprayed two models as a test with Future floor wax. Four coats about 45min a part with airbrush. I like what I see. It has been four days since and they are semi gloss and hard and much more firm then a typical paper model. I used it straight with a cheap airbrush and clean up with ammonia ie windex or ammonia mixed with water. I have not shot clear plastic or wire rigging this will be my next test. Looks good.
John
|
|
Talha
Full Member
Posts: 119
|
Post by Talha on Jul 20, 2007 6:28:04 GMT
i used acrylic lacquer but the model looses its shine after a few days probably because of dust. it doesnt ruin the paper or colours of the model. if anyone plans to do this just remember spray the entire parts sheets then assemble because if done afterwares the model becomes deformed. oh and place the model in a dust free area after making!
rookie
|
|
nazzii
Junior Member
Posts: 85
|
Post by nazzii on Jul 20, 2007 6:50:03 GMT
i use very simple stuff:pva glue mixed with few drops of vater and i paint that with paint brush.
|
|
|
Post by dizudasky on Aug 29, 2007 23:54:00 GMT
i have buyed a clear coat in spray, and i finished with it a model im doing now, soon i will post the results, and are very good!!!!
|
|
sb70
New Member
Posts: 7
|
Post by sb70 on Sept 9, 2007 0:40:26 GMT
I use krylon as a spray fixitive for pencil drawing. Comes in an aerosol can in eith matte (non gloss), or gloss finish. The idea for it's use in that medium is to hold in the pencil graphite to avoid smearing while working on different areas of a sketch. The gloss really seemed to add that 'sheen' to paper similar to the effect you might be looking for with sheet metal.
That in combo with glossy paper should yield a pretty good result.
|
|